Door counter system for entry people counting:
TK bus passenger Counting system can automatically, intelligently, accurately gather the number of passengers getting on / off,time statistical control for passenger flows at every station,and the information detection management system of vehicle operation analysis.
The vehicle-mounted passenger flow counter is applied into the passenger counter with the function of automatic statistics of the total number of passengers getting on and off the passenger car. The number of passengers is displayed on the built-in LCD display screen. The display screen data can be saved for over 2 years under the circumstance of outage. The passenger counter data can be reset with the key switch in order prevent from artificially destroy data integrity.
Communication baud rate:9600bps
Max mounting distance between emitter and counter: 3m
Anti-vibration ability: amplitude 0.35mm, 60-200Hz; ACC 50m/s2
Temperature range: -20 ~ +65℃
Working voltage: -20 ~ +65℃; voltage fluctuation: 15%
Detectable max traffic speed : 6m/s
Respectively install the vehicle-mounted passenger flow counter and baffle-board at the two sides of the car door. When there no passengers going on and off, the infrared signal launched by the built-in launcher of the vehicle-mounted passenger flow counter reflects and is received through baffle-board and the infrared signal strength is strong enough and can penetrate through the glass of car door. Therefore, the vehicle-mounted passenger flow counter and baffle-board can be installed behind the glass of car door, but it’s necessary to purchase door contact switch component separately to be used in case of errors arising from the activity of filter car door. When the passengers keep out the infrared signals reflected by the baffle-board while getting on and off, the vehicle-mounted passenger flow counter will count the number of the direction of getting on or off once according to the direction that the passengers keep out the infrared signal. The data will be displayed through LCD display screen according to the set direction.
1. The vehicle-mounted passenger flow counter is installed at one side the car door that is as high as 800-1300mm away from the footboard of the car door; in case that the car door is equipped with the multi-step footboard with large slope, it is necessary to reduce the installation height. It should be installed according to the actual gesture chest height of the passengers when getting on the car, but it should not be installed in the position for the fixed installation with the scope of the activity of the door leaf of the car.
2.The distance between the baffle-board and the passenger flow counter should not longer than 3000mm.
3.In case that the car door footboard refers to the stair-type footboard, it is necessary to appropriately reduce the installation height to ensure the passenger flow counter is appropriately in the position of the chest of passengers when they get on the car and their body bends forward.
Installation of baffle-board:
After completing installation of passenger flow counter, install baffle-board according to the position corresponded by that of passenger flow counter. Baffle-board is applied to reflect the infrared beam launched by the passenger flow counter in order that the passenger flow counter could detect the infrared beam signal. The infrared beam is invisible light. Whether the baffle-board is in the correct position can be determined according to the two LD indicator lamps on the panel, which is as shown by the following fig.
When baffle-board is within the scope of infrared beam, the two action indicator lamp on the passenger flow counter panel will be off, through which whether the baffle-board is in the correct position can be determined.
Gate control switcher:
Gate controlled switch must be applied with magnetic mass by which the magnetic switch is on with magnetic field around it. If there are no magnetic field around the switch or the intensity of magnetic field is less than the required level, the switch is off.
Gate controlled switch shall be installed near the rotating column of the bus door or above the door leaf, so the intensity of the magnetic field would fluctuate according to the distance variation, producing signal 0 or signal 1. Thus,the switch can detect if the bus door is open or close.
Shipment and payment:
4-8 days for samples;15-30 days for bulk order
Terms of payment
T/T,L/C, Western Union
5000 pieces / month
Xiamen Xinsenyue Mechanical & Electrical Co.,Ltd. is the manufacturer of "sop arm","automatic passenger counter & GPS system","automatic bus LCD monitor","Car gas leak alarm system","Bus Patrol System","Image capture"…,
* We are the manufacturer,
* Would provide good quality product,
* Can save your money,
* Can provide better service,
* OEM or ODM is OK.
Q: Are you a factory or trading company?
A: We are the Manufacturer, established in 2007, ISO certificated factory.
Q: Where is your company and factory located? How can I visit you?
A: Our factory is located in 405-2 Xin'an,xinyang street,Haicang district,Xiamen City,Fujian province,China. All our clients, from home and abroad, are welcomed to visit us.
Q: How can I get some samples?
A: We are honored to offer you samples, please feel no hesitation to contact us.
Q: How does your company and factory do regarding quality control?
A: Quality is priority. Highlight always attach great importance to quality controlling from the very beginning to the very end. Our factory comply with the IS09001 standard strictly.
Q: What is your MOQ?
A: Any quantity is acceptable for your order. And the price is negotiable for large quantity.
Q: When will you make the delivery?
A: We can make the delivery within 1-15 working days according to the quantity of your order.
Q: How can I contact you now?
A: Tel: +86-592-2033185
Mobile phone: 0086 15980823521
Mobile phone: 0086 15980823521